Ti Bq25155 Battery Power Charge Management Chip Electronic Components Integrated Circuit IC.

• shape: Flat
• Conductive Type: Bipolar Integrated Circuit
• Integration: MSI
• Technics: Semiconductor IC
• Rating: Catalog
• RoHS: Yes
• Model NO.: BQ25155
• Reach: Yes
• Operating Temperature Range (°c): -40 to 125
• Transport Package: 250 Small T&R
• Trademark: TI
• HS Code: 8542399000
• Production Capacity: 60000

Product Description

Quality information

RatingCatalog

RoHSYes

REACHYes

Lead finish / Ball materialSNAGCU

MSL rating / Peak reflowLevel-1-260C-UNLIM

Packaging information

Package | PinsDSBGA (YFP) | 20

Operating temperature range (°C)-40 to 85

Package qty | Carrier250 | SMALL T&R

Features for the BQ25155

• Linear battery charger with 1.25-mA to 500-mA fast charge current range
  • 0.5% Accurate I²C programmable battery regulation voltage ranging from 3.6 V to 4.6 V in 10-mV steps
  • Configurable termination current supporting down to 0.5 mA
  • 20-V Tolerant input with typical 3.4-V to 5.5-V input voltage operating range
  • Programmable thermal charging profile, fully configurable hot, warm, cool and cold thresholds
• PowerPath management for powering system and charging battery
  • I²C Programmable regulated system voltage (PMID) ranging from 4.4V to 4.9V in addition to battery voltage tracking and Input pass-though options
  • Dynamic power path management optimizes charging from weak adapters
  • Advanced I²C control allows host to disconnect the battery or adapter as needed
• I²C Configurable load switch or up to 150-mA LDO output
  • Programmable range from 0.6 V to 3.7 V in 100-mV steps
• Ultra low Iddq for extended battery life
  • 10-nA Ship mode battery Iq
  • 400-nA Iq While powering the system (PMID and VDD on)
• One push-button wake-up and reset input with adjustable timers
  • Supports system power cycle and HW reset
• 16-Bit ADC
  • Monitoring of charge current, battery thermistor and battery, input and system (PMID) voltages
  • General purpose ADC input
• Always on 1.8-V VDD LDO supporting loads up to 10 mA
• 20-Pin 2-mm x 1.6-mm CSP package
• 12-mm² Total solution size

Description for the BQ25155

The BQ25155 is a highly integrated battery charge management IC that integrates the most common functions for wearable and portable devices, namely a charger, a regulated output voltage rail for system power, ADC for battery and system monitoring, a LDO, and push-button controller.

The BQ25155 IC integrates a linear charger with PowerPath that enables quick and accurate charging for small batteries while providing a regulated voltage to the system. The regulated system voltage (PMID) output may be configured through I²C based on the recommended operating condition of downstream IC's and system loads for optimal system operation.

The device supports charge current up to 500 mA and supports termination current down to 0.5 mA for maximum charge. The battery is charged using a standard Li-Ion charge profile with three phases: pre-charge, constant current and constant voltage regulation.

The device integrates advanced power path management and control that allows the device to provide power to the system while charging the battery even with poor adapters. The host may also control the power path through I²C allowing it to disconnect the input adapter and/or battery without physically removing them. The single push-button input eliminates the need of a separate button controller IC reducing the total solution footprint. The push-button input can be used for wake functions or to reset the system.A 16-bit ADC enables accurate battery voltage monitoring and can be used to enable a low Iq gauging to monitor battery health. It can also be used to measure the battery temperature using a thermistor connected to the TS pin as well as external system signals through a pin. The low quiescent current during operation and shutdown enables maximum battery life. The input current limit, charge current, LDO output voltage, and other parameters are programmable through the I²C interface making the BQ25155 a very flexible charging solution. A voltage-based JEITA compatible (or standard HOT/COLD) battery pack thermistor monitoring input (TS) is included that monitors battery temperature and automatically changes charge parameters to prevent the battery from charging outside of its safe temperature range. The temperature thresholds are also programable through I²C allowing the host to customize the thermal charging profile. The charger is optimized for 5-V USB input, with 20-V absolute maximum tolerance to withstand line transients. The device also integrates a linear regulator to provide a quiet rail for radios or processors and can be independently sourced and controlled through I²C.